Sears Craftsman Shaper - Woodworking Talk
2011年7月21日 · I know this is an old thread and an old shaper from Sears/Craftsman, but the bearings used in the spindle are as follows: 6202-5/8-2RS This means this is a special 6202 series bearing with a 5/8" inside diameter for the shaft. The 2RS means that the side of these ball bears have 2 rubber seals.
what do I do with these old craftsman 'shapers'?
For some reason these seem to follow me home. I have two old craftsman 'shapers'. They are cast iron, and have a nice mechanism for raising and lowering the bits. A 1/2 hp motor with them. I want them out of my shop. Or I want to 'do' something with them. (may very well end up in the scrap pile if not).
Opinions on vintage Craftsman Shaper table 113.
2016年6月8日 · I had an old Craftsman shaper for several years. They are very simple machines. There is not a whole lot that can go wrong. I sold mine after I made a router table with a 3hp router. I didn't think I needed both. After several years, I can say the router table works for me. I have never wished for the shaper again.
Help with a Craftsman shaper - Woodworking Talk
2009年4月20日 · They have shaper cutters for the 1/2" arbor on the Craftsman Shaper. the prices look very reasonable. As soon as I get the shaper cleaned and ready for service, I'm going to pick up some shaper cutters from these folks. I even saw a deal for six cutters for like $55.00. Hope this is useful to you.
Craftsman Shaper Cutters
2024年4月4日 · Craftsman Shaper Cutters ? I was given three sets, a couple of smaller three cutter ones (2 1/2" ?) and one with a single cutter (4 1/2" ?) . I have a 3hp shaper, so I might use the smaller ones .
Craftsman Shaper Model 113.23930 - Woodworking Talk
2012年11月16日 · Yesterday I was given the above mentioned shaper. It had been stored in an old garage and has a lot of surface rust on the cast iron table. Can anyone help with suggestions on how to clean it up. The spindle shaft also is rusted. I was able to find an owners manual that looks identical to the one I have. It is model nr. 112.239201.
Spindle nut for craftsman shaper 137.217100 - Woodworking Talk
2023年8月8日 · Craftsman 137.217100 Manual Online: Parts List And Diagram. CRAFTSMAN SHAPER / ROUTER When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this shaper/router may...
Old Craftsman Shaper Problem - Sawmill Creek
2013年7月14日 · Help, please. I found an old Craftsman Shaper, model-113.239.20, serial-8236-00023, at an auction. Then I found its manual on-line. Someone made a stand for it. I will get a motor and cutters if I can resolve a missing parts problem first.
older Sears Craftsman Shaper - Sawmill Creek
Looking for a good source for 1/2 inch Shaper cutters for a Sears Craftsman Shaper I got. Sears is pretty much useless when it comes to replacement parts for their older machines. This one was made back around 1985 , I believe. It has the steel stand and cast Iron table.
Shaper: to sell or not to sell - Woodworking Talk
2012年3月14日 · Recently I inherited a Craftsman shaper, 2hp, 1/2 arbor. I already have a really good router and table. Router I have now is capable of 3-1/2 inch bits....the shaper is only capable of 2-1/2" cutters. The problem I'm having is finding 1/2 shaper cutters. The shaper itself is in really good condition, looks like it was hardly ever used.